replacement window handle UPVC Door Handles

Whether you're replacing your handles or adding a little more security, you can find the right handle for your door. These upvc handle are easy to install and have the required 92mm centre distance of multipoint locks.

The backplate's fixing centre as well as the keyhole/lever dimensions are the most important measurements. Check these carefully against your current measurements prior to ordering.

Lever/Pad

Lever pad door handles are made up of the lever handle on one side and a paddle shaped handle on the other. These are designed for use with key wind locks. However, they can be fitted to multipoint split spindle door locks.

Our selection of upvc handle lever pads are available in a variety of finishes and these will be shown in the drop down list once you have found the correct handle for your door. Some styles of handles are not available in all finishes. You should always check the technical drawing and dimensions for the item that you want to ensure that you receive the right size and fit.

It is essential that when choosing the new set of Upvc Window locking handles lever pad handles, they match the PZ (distance from the handle spindle to the middle of the hole in the cylinder) of your multipoint door locks. This is because these must be lined up to ensure that doors stay locked, regardless of whether you are viewing them from the inside or from the outside. The handles we offer are designed to work with a variety of conventional cylinder locks, however you should double glazed window handles-check prior to ordering.

You'll need to take off the handles on your current handle and remove the lock case if upgrading to dual spindle levers for your handle since this will require an additional split inline cylinder. They can be purchased separately, and we provide an entire technical diagram to examine in the images for each product.

It is a good idea to loosen the screws holding your existing door handle and then inspect the mechanism. If the screws aren't loose enough, you may need to loosen them more. Then you can remove the spindle from the door handle and replace it with your new upvc handle. Before screwing the handle into place it is recommended to make sure it is in the correct position. You can do this by putting your finger in the gap between the door frame and the handle to ensure that it is in a level position.

Lever/Lever

Lever door handles operate with a multi-point lock that utilizes a Euro cylinder and are found on the majority of double doors made of aluminium, upvc doors, and some wooden doors. They feature an inside lever and a paddle on the outside and are generally available in two types. Sprung - they come with a spring cassette within the backplate to help bring the handle lever to an upright position. Non-sprung: They do not include a mechanism that can spring the handle lever to a horizontal angle.

To fix a sagging lever door handle you must find the hole for access to the detent or pin, which is typically an elongated or rectangular shape hole or protruding pin situated on one side of the handle base plate. Once you have located the hole for accessing the detent or pin, you can remove it with the help of a screwdriver.

Once the handle is in a horizontal orientation, you can re-install the screws and tighten them to make sure the handle is secured to the base plate. It is also advisable to apply an adhesive that locks the screw threads to improve the grip and prevent them from loosing over time.

There are a myriad of reasons that door handles for levers droop. The most frequent reason is that the fixings have been over tightened and are putting stress on the bearings of the lever, which causes it to become a bind on the door's surface. It could also be because the levers aren't being operated at a straight angle and this is compressing the latch mechanism preventing it from fully springing back into service.

A common cause of a spring lever not operating properly is the spring not being in the right position on the backplate. The most effective way to determine this is to turn the handle and see whether it returns to its horizontal position.

If your door handles are loose, it is essential to spot the problem quickly, as this can lead to excessive wear on the screws, and even to the handle falling off of the base plate. It is also a good idea to tighten all loose screws on a regular basis in order to prevent them from becoming loose.

Lever/Snib

These upvc door handles are also referred to as 'Snib' handle sets and have a snib lever at the top of the lever that you can press down to lock your door in the event that you don't have a dummy lock. They are typically fitted with a Fullex 68PZ (that's 68mm between the spindle's center and lever or the lock centre) door lock. We also stock a range of door handles 68PZ from brands like Ferco and Fab & Fix.

Change your door handle is an inexpensive way to update your home, whether you're replacing your handles or installing new ones to doors you've built in your house. There are a variety of upvc door handle available with traditional levers on backplate, curved or straight short latches and knob handles with dummy handles for multi point locks, which are ideal for French doors.

Lever on backplate handles are often rectangular, but there are also oval or circular-shaped versions that are referred to as rose door handles. These handles are identified by a lever or a knob that is mounted on the backplate. The backplate can be removed for hidden fixing.

These handles are available in a variety of finishes, including chrome and coloured finishes to match your door and other hardware such as knobs, hinges and bolts. Some handles come with grub screw to attach the knob or lever to the spindle. Other handles are supplied with bathroom spindles that can be used to operate bathroom locks. They feature a thumbturn turn as well as a release mechanism, perfect to use on doors for bathrooms.

Mortise

If your uPVC front door handle is stuck in the open position, the cause will most likely be with the tubular latch. It could be due to a number of things but the most prevalent is a lack of lubrication in the latch plate. This can be corrected quickly by opening the door and spraying lubricant on the handle and lock. Alternatively, it could be that the latch plate has become separated from the backplate. This can be a bit more problematic and would require a professional to fix it.

A multipoint door handle system is the ideal solution to the problem of a sticking door handle. These handles are attached to the faceplate and operated by the use of a key or thumb turn knob that activates the cam that locks the deadbolt. The handles come in different sizes to fit various kinds of uPVC doors and are available in various attractive finishes that are compatible with the hardware that is currently in use. These handles can be purchased on the internet or through an authorized locksmith in your area. They are simple to install, with clear instructions.

You will have to know your PZ cylinder's size to select the right replacement door handles handle set. This is the distance in millimetres between the inside edge of the frame of the door and the centre of the hole for the handle. You should also know if your door has a hook style lock or a mortise style lock. Once you know these measurements, the most efficient method to determine the right handles is to use the filter by brand option on the website. This will narrow down the choices and allow you to choose the appropriate size from there.

A typical handle set comes with the handle unit and a pair of different length screws, drill guides and installation instructions. Smart versions, like the Igloohome Smart Mortise 2+ include a mortice lock complete with a keypad. These are more sophisticated units that are best suited to professional installers or highly competent DIYers. Some handle sets include a range of other accessories, such as weather strips that can be used to enhance the appearance of the door.