How to Replace a Kia Sportage Replacement Key

For a number of Kia models the key comes with a built-in keyless entry system. The key is usually akin to an electronic remote and can be changed with a fresh one from an Kia dealer or locksmith.

Key fobs may stop working due to a number of reasons, including batteries that are dead, worn-out buttons signal interference or water damage. Here are some guidelines on how you can get your Kia Sportage replacement key back to working.

How do you replace the remote key or smart key?

The battery inside your Kia's smart key will eventually need be replaced, whether it's a remote key or a push-to-start one, or a normal metal key that does not contain a transponder. This is especially the case if your car displays a message indicating that the remote or smart keys are in poor condition.

Fortunately, it's quite simple to do. To replace the battery in the keyfob remove your mechanical key from the slit at the back of the fob. Then, pry the cover open. Inside the key fob will be an incredibly small screw that holds the battery in its place. Take out the old battery by detaching the screw with a small screwdriver. Insert the new battery and close the cut on the key fob.

Once the key fob has new batteries, test it by pressing the locks and unlock buttons. You're good to go If the doors lock and unlock as expected. You can now take advantage of your kia new key's hands-free lock/unlock feature whenever your fingers get chilly or you have to run some errands in Brandon.

Note: Certain key fobs (transponder chip or smart keys) may need to have their programming completed. This requires a special programming machine that only the dealer or automotive locksmith has access to. Other keys (non-transponder metal keys) do not require programming. If you want to change the programming of your key, it is necessary to record the key code number on the tag for the key code.

How To Find A Lost Kia Key Fob do I replace the battery?

If the 2011 kia sportage key fob key fob does not respond to pressing the lock/unlock button, it's likely that the battery is low. A low battery could cause other issues like the check engine light turning on or delayed engine cranking. Fortunately, replacing the key fob battery is a fairly simple DIY project that requires only a few basic tools.

Make sure to shut off your vehicle and close all doors before you begin. Locate the small metal or plastic piece at the bottom of your key fob, and jiggle it until a metal key is released. You can then insert the key in the door handle of the driver to unlock your car.

To replace the battery inside the key fob, take off the cover on the rear. Make use of a plastic pry tool to loosen the latch that holds the black negative cable. Remove the old battery, and then align the new one in a way that the "+" positive side faces you, and the "negative" negative side is facing the fob's electrical contacts made of metal. Avoid using too much force when pushing the new CR2032 into place to avoid damaging or breaking the metal contacts.

After installing the new battery and turning the key fob on and off in the ignition until the door locks up. Then you can test your Kia key fob for kia optima fob to check if it is working properly again.

How can you replace the smart key?

You may have either a standard keyfob, or a Smart Key based on the model of kia sorento replacement key Sportage. The smart key comes with an embedded mechanical key blade, unlike the standard key fob, which does not. Both key fobs are equipped with batteries that will eventually require replacing. It's a fairly simple process that will take about two minutes.

Be sure to switch off your Kia and be on a level and well-lit surface prior to you begin. Be aware that there are tiny components inside the fob that can be snagged if not cautious.

The small release button is located on the lower backside. This will be either a circular button or a rectangular slot. You can open the key fob by pressing the button.

Once you have the key fob opened it is easy to remove the old battery, and replace it. The new battery is a one called CR-2032 and can be purchased from a local or online auto parts store. After you've finished, your key fob should allow you to lock, unlock, and start your vehicle, even if it isn't running.

How to replace a mechanical key

The Kia keyfob is an excellent convenience which allows us to lock or unlock our car by simply pressing a button. But, as with all devices, it can have problems occasionally. Luckily, there are steps that can be taken to fix these issues and keep our key fobs in good condition for the long run.

One of the most frequent problems is a dead or dead battery. This can cause your device to stop working or operate intermittently. If this is the issue it is time to replace the battery a new one.

If this isn't enough to resolve the problem then try using a normal flat-head screwdriver to break open the fob's plastic casing. Be careful not to damage any internal components or scratch the plastic. After the battery has been removed and replaced, you can replace it with a brand new battery.

Once the new battery is in, shut and open the doors using the mechanical key (every Kia fob comes with an emergency mechanical key that can fit into the slot). Test the key fob and ensure that it's working properly. Contact a dealer or locksmith to solve the issue if the fob is still not working. To avoid future lockouts, ensure that you have an emergency key that can work on all door and trunk cylinders.