Peugeot 208 Key Replacement

It is best to delegate the replacement of peugeot 107 spare key 208 keys to auto locksmiths equipped with the necessary equipment and technical knowledge. They can create and program new keys much faster than a dealership would and at a lesser cost.

A dead battery for your coin is most likely to be the cause if your key fob stops locking or unlocking doors. There are other reasons that the key could be malfunctioning.

Dead Coin Battery

A dead coin battery will stop your peugeot key programming 208 from locking or unlocking and cannot start the engine. In this case, you will need to employ the alternate method of starting as described in your vehicle's owner's manual.

The spark plugs may also be worn out. The spark plugs ignite fuel to start the engine. However they have a short lifespan. They will eventually break down in the event that they aren't utilized enough.

Luckily, there's an easy solution for this problem. Examine the voltage of your battery with a multimeter. If it's lower than 11.5 Volts, then you need to replace it. If the battery is corroded, it is important to clean its contacts. This can be accomplished by removing the rubber cover from the two terminals of the battery, and then using a wirebrush to eliminate any corroded parts of the battery. Then, reconnect the positive and negative pole cables.

Water Damage

If your 208 doesn't start and the battery has not failed, you should check the spark plugs. You might find that they are simply too filthy and don't spark. This can be fixed by cleaning the spark plugs in an workshop.

Peugeot automobiles use a key with a transponder compatible with the immobiliser. This makes sure that only the correct key can turn the engine. If the chip inside the Peugeot key is damaged, it will not send the proper signal to the vehicle.

Water damage is the most common cause of this problem. This is a typical issue in colder climates where the vehicle is exposed to rain or snow. If this is the case, contact a reputable auto locksmith who has all of the equipment and tools needed to modify the new key. They will also have the latest technology and equipment required to make a Peugeot smart key. The process shouldn't take more than 15 minutes.

Contacts to the battery are not working properly.

Peugeot replaced the old transponder chips using a new type that uses electronic components mounted on a circuit board. The new system is great when it's new, however the circuit boards begin to degrade with time and cease to function properly.

This could prevent the immobiliser from working, so your vehicle will not start. If this is the case it's a good idea to seek out a peugeot van key specialist or locksmith.

Another issue that is common is when the battery for the key fob starts to die, this causes the blade of the key to stop feeding into the lock. A locksmith from your vehicle can replace the battery and cut a new blade for you, this is normally a quick fix.

Faulty Receiver Module

If your Peugeot key fob isn't working after dropping it on the floor, getting exposed to a sudden downpour or accidentally washing it, it could be due to a defective receiver module. The receiver is responsible for transmitting radio frequency signals to the onboard computer which controls the centralized locking system in your Peugeot vehicle.

The key fob itself has rubber seals that block water from getting to the electronic chip inside. The chip can be damaged by water if it is exposed to water for a long time. The high salt content of the pool or ocean water can cause damage to the key fob if it is submerged.

If your Peugeot spare key fob doesn't work it is necessary to have the module replaced. This can only be performed by a professional auto locksmith or Peugeot specialist. Like other automobiles, Peugeot keys are protected by an immobilizer that is unique and requires the correct coding to start the engine. This is the reason why you should only trust an experienced Peugeot locksmith with the task of designing and programming the replacement.

Computer with a problem on board

The computer on board in your Peugeot is the one responsible for all of the systems in your car, from power windows to airbags. The computer on board will display the code when something goes wrong. This code will be stored within the system until the issue is fixed. In most cases, this will require replacing the on-board computer.

The most typical reason for the warning light for airbags to illuminate is corrosion or loose connections within the sensor. This can occur due to wear and tear, ageing or exposure to salt and moisture. This issue should be taken care of as soon as you can, because an airbag that's malfunctioning could be dangerous in case of an accident.

If you notice the error "card not found" on your peugeot partner key fob programming, the key battery in the key fob could be dead or weak. This will stop the key fob from sending a signal to disarm your vehicle's immobilizer. You can test this by pressing the unlock button on the key fob and then trying to start your car. If this does not work then the battery in the key is in need of replacement.