Peugeot 208 Key Replacement

peugeot 3008 key fob not working 208 key replacement is best left to experienced auto locksmiths who have the proper tools and know-how. They can make and program new keys quicker than a dealership and at a lower price.

If the key fob stopped locking or unlocking your doors, it is likely due to a dead battery in the coin. But, there are other possibilities that the key is malfunctioning.

Dead Coin Battery

A dead battery in the coin compartment will hinder your Peugeot 208 from locking or unlocking and won't start the engine. If this is the scenario, you'll need make use of the backup starting procedure that is described in the owner's manual for your vehicle.

The spark plugs might also be worn out. The spark plugs ignite fuel to start the engine. They have a limited lifespan. If they are not used enough, they will eventually fail.

There is a simple solution to this problem. Examine the voltage of your battery using a multimeter. If it is below 11.5 Volts, then you need to replace it. If the battery has corroded it is necessary to clean its contacts. This can be done by lifting the rubber covers covering both battery terminals and using wire brushes to clean any corroded components of the battery. Then, you must reconnect the positive pole cables to the negative.

Water Damage

If your 208 will not start and the battery hasn't been replaced, you must examine the spark plugs. It could be that they're dirty and they don't spark. The spark plugs can be cleaned in the workshop.

peugeot boxer replacement key cars use transponder keys that integrates with the car's immobiliser system. This ensures that only the correct key is able to turn the engine. If the chip in the Peugeot key is damaged, it will not transmit the correct signal to the vehicle.

This is a very common issue that can occur due to water damage. This is a common issue in areas with colder temperatures where the vehicle is exposed to snow or rain. In this instance, you should contact an experienced locksmith who has the required tools and equipment to change the key's programming. They will also have the most up-to-date technological know-how and the equipment required to create the Peugeot 208 smart key. The process shouldn't be more than 15 minutes.

Faulty battery contacts

peugeot 206 new key changed from the old carbon-encased transponder chips to an entirely new type of chip that incorporates electronic components on circuit boards. The new system is fantastic when it's new, however the circuit boards begin to degrade with time and stop working properly.

This can stop the immobiliser chip activating the immobiliser chip, causing your car not to start. Contact an Peugeot specialist or a locksmith if this is the case.

Another issue that is common is when the battery for the key fob starts to die, this causes the blade of the key to stop getting into the lock. A locksmith for cars can replace the battery and cut a fresh blade for you, it's normally a quick fix.

Faulty Receiver Module

It could be that the receiver module has a problem in the event that your Peugeot key fob doesn't work after being dropped on the floor, or exposed to a stormy rainstorm, or accidentally washed. The receiver is responsible for sending radio frequency signals to the on-board computer, which is responsible for controlling the centralized locking system within your Peugeot vehicle.

Rubber seals on the key fob block water from reaching its electronic chip. However, prolonged exposure to water could be able to penetrate these seals and cause damage to the chip. Submerging the key fob into ocean water on the beach or throwing it into the water can be particularly damaging due to the high salt content.

If your Peugeot spare key fob stops working it is necessary to have the module replaced. This can only be performed by a professional auto locksmith or Peugeot specialist. Unlike other cars, Peugeot keys are protected by an immobilizer that is unique and requires the correct coding to start the engine. This is why you must go with a knowledgeable Peugeot locksmith for the job of creating and programming an alternative.

Computer malfunctioning on-board

The on-board computer in your peugeot 406 key fob is responsible for many of the features in your car, including power windows and airbags. The on-board computer will show a code when something goes wrong. This code is saved in the system and will stay there until the problem has been resolved. In most cases, this will require replacing the onboard computer.

The most common cause of the warning light of the airbag to turn on is corrosion or loose connections within the sensor. It can be due to wear and tear, aging or exposure to moisture and salt. This issue must be addressed as soon as you can, because an airbag that is not functioning could pose danger in the event of an accident.

If your peugeot 508 key is showing a card not detected error, then the key battery in the key fob might be weak or dead. This can prevent the key fob from transmitting a signal that will disable the immobilizer on your vehicle's standard. Test this by pressing the unlock button on the key fob and then trying to start your car. If this fails it is because the battery of the key has to be replaced.